Whitford coatings suited for oil & gas and fastener applications.
| Any mating surfaces that requires dry lubrication in low contact pressure applications such as rotary actuators, carburetors, bearings, seat belt clips, actuators, etc. |
1010 |
Resin-bonded PTFE, thermoset, dry-film lubricant designed for conventional spray techniques. It is used to reduce friction, prevent scoring and galling, or provide secondary lubrication in the event of failure of the primary (conventional) lubricant. |
| Any mating surfaces that requires dry lubrication in moderate contact pressure applications, such as fasteners, threaded components, hinge pins, piston casings and compressors. |
1014 |
Resin-bonded PTFE, thermoset, dry-film lubricant designed for conventional spray techniques. It is primarily used on studs and bolts to prevent corrosion and facilitate make-up torque. Because of its predictable, low-friction properties, less “make-up” torque is required to produce the specified tension. During assembly, clamp loads are increased; “scatter” is reduced. Friction values are predictable and significantly enhance conventional surface treatments such as phosphate and platings. The low-friction properties also reduce “break-out” torque, which allows removal of bolting with a wrench instead of a blowtorch. |
| Oil tools, pumps, valves, actuators, impellers and offshore components. |
1212 |
Resin-bonded, thermoset, non-lubricated coating designed for conventional spray techniques. It is used as a stand-alone thin film, corrosion resistant, barrier coating, or as a primer for Xylan 1213. |
| Metal seals, collet connectors, offshore components and other applications to reduce wear of bearing surfaces under high load. |
1213 |
Resin-bonded, thermoset, dry-film lubricant designed for conventional spray techniques. It is formulated for high contact pressure, low-speed, wear applications and provides long-term lubrication for bearing surfaces subjected to extreme pressures. The coating is heavily loaded with MoS2 (no PTFE) and is superior to “moly” greases which wash away. Xylan 1213 is clean to the touch, unlike other moly coatings that leave a soot-like residue. |
| Valves, oil tools, chemical processing equipment, offshore components and down-hole tools. |
1311 |
Resin-bonded, thermoset, minimally lubricated coating designed for conventional spray techniques. A tough, economical, single-film PPS/PTFE coating. This product contains a small percentage of PTFE lubricant. Recommended for use when abrasion resistance is the primary characteristic sought and lubrication and/or nonwetting properties are secondary considerations. |
| Valves, oil tools, chemical processing equipment, offshore components and down-hole tools. |
1331 |
Resin-bonded PTFE, thermoset, lubricated coating designed for conventional spray techniques. A tough, economical, single-film PPS/PTFE coating. This resin-bonded coating is virtually unaffected by any solvent to 205°C (400°F). It contains a high percentage of PTFE and is recommended for use when a lubricious nonstick surface is desired. |
| Valves, oil tools, riser connectors, chemical processing equipment, offshore components and down-hole tools. |
1391 |
Resin-bonded, thermoset, non-lubricated coating designed for conventional spray techniques. A tough, economical, single-film PPS coating. This resin-bonded coating is virtually unaffected by any solvent to 205°C (400°F). May be used as stand-alone material for excellent corrosion, chemical and abrasion resistance or as a primer for Xylan 1311 or 1331. Combined, they provide an excellent two-coat system for the chemical processing industry. |
| Components needing a corrosion resistant coating, but dimensional tolerances do not permit a thick-film coating. Fasteners and threaded components for oil and gas, chemical processing, building, roofing or appliance industries. |
1400 |
Resin-bonded, thermoset, minimally lubricated coating designed for conventional spray techniques. A recoatable ”RC" coating developed to protect large fasteners from chemical exposure (especially those with high pH). Although it contains a small percentage of PTFE lubricant to facilitate installation and prevent galling, it is considered a barrier coating rather than a dry-film lubricant. |
| Fastener class coating. Any mating surfaces that requires dry lubrication in moderate contact pressure applications, such as fasteners, threaded components, hinge pins, piston casings, compressors. |
1424 |
Resin-bonded PTFE, thermoset, VOC compliant, dry-film lubricant designed for conventional spray techniques. It is primarily used on studs and bolts to prevent corrosion and facilitate make-up torque. Because of its predictable, low-friction properties, less “make-up” torque is required to produce the specified tension. During assembly, clamp loads are increased; “scatter” is reduced. Friction values are predictable and significantly enhance conventional surface treatments such as phosphate and platings. The low-friction properties also reduce “break-out” torque, which allows removal of bolting with a wrench instead of a blowtorch. Note: VOC compliance applies to USA only. |
| Applications to prevent wear of mating surfaces under extreme load such as bearings, valve springs, offshore components and down-hole tools. |
1425 |
Resin-bonded, thermoset, VOC compliant, coating designed for conventional spray techniques. It is formulated for high contact pressure, low-speed wear applications and provides long-term lubrication for bearing surfaces subjected to extreme pressures, up to 150,000 psi (10,500 kg/cm2). The coating uses a unique dual lubrication system of PTFE and MoS2 and is superior to “moly” greases which wash away and PTFE coatings which “cold flow.” Resin-bonded lubricants in Xylan 1425 stay on the job, even in harsh chemical environments. Note: VOC compliance applies to USA only. |
| Fasteners and threaded components. Suited for repetitive make-and-breaks. |
1427 |
Resin-bonded PTFE, thermoset, VOC-compliant, dry-film lubricant designed for conventional spray techniques. It is primarily used on studs and bolts to prevent corrosion and facilitate make-up torque. Because of its predictable, low-friction properties, less “make-up” torque is required to produce the specified tension. During assembly, clamp loads are increased; “scatter” is reduced. Friction values are predictable and significantly enhance conventional surface treatments such as phosphate and platings. The low-friction properties also reduce “break-out” torque, which allows removal of bolting with a wrench instead of a blowtorch. Note: VOC compliance applies to USA only. |
| Threaded fasteners; dip spin parts, small components; screws. |
5110 |
Internally reinforced with titanium for improved wear / abrasion resistance, two-coat, high cure, PTFE based, nonstick, coating system designed for a coil coating application technique. |
| Threaded fasteners; wood screws. |
5164 |
This resin bonded, lubricious, coating is designed to be applied by a dip spin technique. |
| Threaded fasteners, particularly for the automotive industry. |
5230 |
This resin bonded, coating which is intended to be applied by a dip spin technique is designed to protect small fasteners from corrosion caused by road salt, acid rain and other forms of environmental corrosion. It offers controlled torque tension coupled with excellent corrosion resistance. |
| Threaded fasteners for the building industries, including the roofing and appliance industries; fasteners; stampings; end caps; screws. |
5250 |
This resin bonded coating, designed for application by a dip spin technique, has a low level of PTFE to facilitate driving through metal without encouraging backout. Lots of colors available. |
| Threaded fasteners for the building industries, including the roofing and appliance industries; fasteners; stampings; end caps; screws. |
5270 |
This resin bonded coating, designed for application by a dip spin technique, has a low level of PTFE to facilitate driving through metal without encouraging backout. Lots of colors available. |
| Threaded fasteners for the building industries, including the roofing and appliance industries; fasteners; stampings; end caps; screws. |
5420 |
This resin bonded coating, designed for application by a dip spin technique, has a low level of PTFE to facilitate driving through metal without encouraging backout. Xylan 5420 is a VOC compliant product and is intended to offer an environmentally acceptable alternative to the solventborne materials. |
| Threaded fasteners for the building and appliance industries; fasteners; stampings; end caps; screws. |
5430 |
Xylan 5430 is a protective coating for small fasteners and hardware. It is a VOC compliant coating that provides good corrosion and UV protection. |
| Threaded fasteners for the building, roofing or appliance industries where acid rain resistance is required; stampings; end caps; screws; roofing fasteners; transmission shafts. |
5611 |
A zinc rich primer formulated for application using a dip-spin application technique. It enhances the Corrosion resistant provided by Xylan topcoats as measured in the Kesternich test DIN 50018 acid rain test. |
